What does bonnet removed mean?

The bonnet functions as a cover and guard for the waste port as the globe rotates. The globe will not rotate without the bonnet installed. If a cycle is interrupted or the bonnet is removed, the unit will stop, and the yellow light will flash slowly, about 1x per second .

How do you put the bonnet back on a Litter-Robot?

Litter-Robot 4: Bonnet installation guide Remove the old bonnet: Press and hold the latches on both sides of the bonnet, then lift and rotate the bonnet to its open position. ... Install the new bonnet: Place the bonnet into the hinge behind the robot as shown. ... Press the Reset button to zero the weight sensors.

What is the bonnet on the litter robot 4?

Litter-Robot 4 features a bonnet that covers the globe and functions as a guard for the waste port as the globe rotates . Sensors on the unit detect if the bonnet is on or off. This ensures that Litter-Robot will not rotate if the bonnet has been removed.

What is an example of a bonnet?

Headgear tied under the chin with a string was especially likely to be called a bonnet. Other features associated with bonnets as opposed to hats was that the forehead was not covered, and the back of the head often was. The outdoor headgear of female servants and workers was more likely to be called a bonnet.

What is the purpose of a bonnet?

Bonnets help protect your hair from friction and breakage caused by contact with pillowcases. They also help retain moisture, reduce frizz, and preserve hairstyles, particularly for individuals with textured or curly hair.

Why is it called a bonnet?

In the UK, a car bonnet is the metal part that covers the engine of an automobile. Bonnet comes from the Old French word bonet, which means a stiffened head-dress like this: A car hood is a North American term, used primarily in America and Canada. Hood comes from the Old English word.

Can a Litter-Robot be repaired?

Yes, we offer repair services . If your unit needs repair, contact our Customer Experience Team to discuss what the options are.

How do you put a Litter-Robot back in the box?

Place the Litter-Robot into the box so it faces the corner and aligns with the cardboard insert on the bottom. Safely pack the power supply inside the rear corner brace (1). Write your name and RMA number prominently on the outside of the box and on an interior box flap prior to sealing the box with tape.

How do you force a Litter-Robot to cycle?

Press and release the Power button to turn the robot ON of OFF. The robot will begin a clean cycle when power is turned on. Press and hold, while at the home position, to enter night light setting mode. Press and release the Cycle button to start a clean cycle .

How do you reset the sensor on a Litter-Robot 4?

To exit this mode, press and hold the Cycle button for 3 seconds. The light bar will change to blue, indicating the mode has been disabled. Press the Reset button while the globe is at the Home position with the blue light bar on to reset the cat sensor(s).

How to fix flashing yellow light on Litter-Robot?

If your Litter-Robot 3 is displaying a yellow light flashing slowly, this indicates a cycle has been interrupted either by the cat sensor or bonnet removal. Press the Reset button to resume the cycle . Success: If your unit returned home and displays a solid blue light, you've been successful.

Litter Robot Bonnet Removed Error: Here's How to Fix it (2024)

Disclaimer: Some of the links in this article may be affiliate links; we will earn a commision, at no additional cost to you, if you make a purchase through one of our links.

It’s a good thing that modernized litter boxes are now an option. Litter Robot is a modern technology that offers big help to fur-parents. This device is specially designed with pre-programmed instructions that allow proper functioning.

However, just like any other technology, Litter-Robot may also malfunction. One of the common issues you may encounter when using the robot is the bonnet connections.

You’ve probably received a notification about your Litter-Robot bonnet removed error.

Is that why you’re here? Well, you’ve come to the right place! Stick around to learn more information.

Litter Robot Bonnet Removed Error: Here's How to Fix it (1)

Table of Contents

Why Do I Keep Receiving The notification litter robot Bonnet Removed Error?

This issue happens if the bonnet isn’t securely placed on the Litter-Robot. It restricts the globe from rotating and you’ll notice a yellow light blinking once per second.

Another reason might be the black key found at the back of the globe. It’s supposed to lift the bonnet if placed in the right slot.

However, if none of these two is causing the error, you can try the following solutions:

Save 35% on All Pet Supplies from Chewy

Re-assembling The Bonnet

1. Unplug The Litter-Robot

Turn off the litter box by pressing the ON/OFF button. Then, unplug the power supply blackjack from the back.

Recommended: Catlink vs Petkit full comparison

2. Remove The Bonnet

To release the bonnet, press the left and right tabs located in the front of the Litter Robot. After that, incline the bonnet top toward the back of the litter box.

3. Clean The Sensors

While the bonnet is removed, clean the two metal sensors using a damp cloth. It can be found on the left side of the bonnet.

4. Re-attach The Bonnet

Hold the bonnet with your two hands. Tilt the bonnet top away from your body so the two rear corner tabs are upright. Slip the tabs into the slots on the base. Next, tilt the bonnet top forward to drop the longer front tabs and insert them into the front slots.

To ensure that the bonnet is secured, press down on its sides and you should feel a snap and hear a ‘click’.

Check The Night-Light Connection

1. Unplug The Litter Robot

Turn off the litter box and unclip the bonnet.

2. Check The Wiring

Inside the bonnet, you’ll see wires and a micro connector. They’re attached to a small circuit inside the light housing. Make sure there’s a proper connection by pushing the micro connector into the circuit board.

If the issue still persists up to this point, you should replace the bonnet with a new one.

What Other Issues I May Encounter With My Litter-Robot?

Here are the other common issues you may encounter when using a self-cleaning litter box.

1. Cat Sensor Fault

Too much weight in the globe can trigger the Cat Sensor. It causes the Litter-Robot to stop mid-cycle and, sometimes, a red light will start blinking. These could be signs that you need to adjust the cat sensor.

Follow these steps to make adjustments to the Cat Sensor:

Turn off the Litter-Robot and remove the globe.
While the globe is removed, turn on the robot and check if the gear is turning.
If the gear is turning:
Turn off the Litter-Robot’s power.
Turn the base upside down so you can see the bottom surface.
Look for the round black adjustment foot.
Turn the adjustment foot clockwise twice (720°).
If the gear isn’t turning:
Push and release the Safety Line found in the base several times.
Do this until you hear a ‘clicking’ noise.
Reboot the Litter-Robot.
If at this point, the gear is turning, reattach the globe.
Let it complete a cleaning cycle. (This means that there’s no need for Cat Sensor adjustment).
In case this still doesn’t work, you may have to contact Litter-Robot customer service.
Reattach the globe and turn the Litter-Robot on.
Let the robot complete a cleaning cycle. If not, repeat step number 4

If the Litter-Robot keeps on stopping mid-cycle, contact their support team.

2. Rotation Error

This is how the globe rotation works: When your cat is done with its business, the globe rotates and moves through a sifter. All the clean litter will be separated from the dirty ones, and the remaining dirty litter will be placed in the waste drawer.

Litter Robot Bonnet Removed Error: Here's How to Fix it (2)

After that, the globe rotates back and will leave you with clean litter.

Recommended: How to reuse crystal cat litter

You may encounter your Litter-Robot turning the wrong way, and this happens due to one of these reasons:

Malfunction in the circuit board
Harness or magnetic sensor issue

In case you’re experiencing a rotation error in your Litter-Robot, it’s recommended to contact their customer service. You may probably need to replace some parts of the robot.

Customer Reviews

Here are some insights from the fur-parents who have used Litter-Robot:

1. Not Worth Buying

Litter-Robot is definitely expensive compared to a traditional litter box. Even though it’s an advanced technology, it’s still prone to malfunction.

2. Too Bulky

It looks big when you look at it, but it doesn’t have enough space for pretty large cats.

3. SafeCat System Is Surprisingly Effective

As soon as the cat put his paws on the ledge to take a peek inside the Litter-Robot, it immediately detected the cat’s weight and stopped the clean cycle.

4. The Whisker App Works Well

It gives accurate reports on the status of the Litter-Robot, and the waste drawer level. The app also provides health information about the cat, its daily input, and so much more.

Related: How to fix the Litter-Robot dump position fault

5. The Product Is Certainly Convenient

For some fur-parents, it’s an amazing product overall. The Litter-Robot is simple to use and easy to set up. It has worked quite well when it comes to eliminating waste odors.

Final Verdict

Litter Robot bonnet removed error is a common problem when using the self-cleaning litter box.

Most of the time, it’s simply because the bonnet isn’t correctly placed in the litter box. If that’s not the case; hopefully, the methods we’ve mentioned helped you fix the error.

If nothing worked for you, it’s probably time to change your Litter Robot’s bonnet.

Knowing what each light indicator means can also help you determine your robot’s status.

Phil Jonas